RV 110 Worm Gear

RV 110 Worm Gear

RV 110 worm gear is suitable for speed ratio10:1-60:1, maximum torque 600N.m. Support B5/B14 flange and 360° omnidirectional installation, IP55 protection, operating noise < 65dB. Suitable for food, medical and other light load automation equipment, maintenance cycle 2000 hours.
Send Inquiry
Description
Technical Parameters

product-550-550

The RV 110 worm gear supports B5/B14 flanged and 360°omni-directional mounting and is available in two output configurations: solid shaft and expanded hollow shaft.Pay attention to lubrication maintenance during use (grease change for the first 200 hours, then supplement NLGI Level 2 grease every 5000 hours).Operating temperature -20℃~80℃, it is strictly prohibited to overload 150%, abnormal need to stop immediately.

 

Worm gear reducer is most prone to oil leakage because of high temperature and structural limitations.However, the risk can be significantly reduced through seal optimization and regular maintenance.It is particularly suitable for food processing, medical equipment and automated production lines.The impact resistance of aluminum box is slightly weaker than that of cast iron, and it is not recommended to be used under heavy impact conditions.How to avoid oil leakage.

 

First.Check the seal status regularly during routine maintenance.Long-term storage should be filled with grease and shaft extension protection to ensure the service life of the equipment.Select the grease according to the bearing load: heavy load needs to choose a small needle penetration, high film strength and extreme pressure performance of the grease.Calcium base grease with good water resistance should be selected in humid environment.

 

Second .oil level check

 

1. Cut off the power supply to prevent electric shock. Wait for the reducer to cool down;

2, remove the oil level plug to check whether the oil is full;

3. Install the oil level plug.

 

Oil inspection:

1. Cut off the power supply to prevent electric shock. Wait for the reducer to cool down;

2. Open the oil plug and take the oil sample;

3, check the viscosity index of the oil: if the oil is obviously cloudy, it is recommended to replace it as soon as possible;

4, for the reducer with oil level plug: check the oil level, whether it is qualified; Install the oil level plug.

 

Oil change:

After cooling, the viscosity of the oil increases and it is difficult to discharge the oil, and the reducer should change the oil at the operating temperature.

1. Cut off the power supply to prevent electric shock. Wait for the reducer to cool down without burning danger;

Note: The reducer should still be kept warm during oil change

Important parameters of RV 110 worm gear

 

Item

Details

Type

Worm Gear / NMRV Reducer

Model

025, 030, 040, 050, 063, 075, 090, 110, 130, 150

Reduction Ratio

1:5, 7.5, 10, 15, 20, 25, 30, 40, 50, 60, 80, 100

Color

Silver/Blue/Grey or Customized as per Customer Request

Material

Housing: Aluminum for RV25-RV90, Cast Iron for RV50-RV150

Worm Gear: Copper-9-4#, Copper-12-2#

Worm Shaft: 20Cr, Carburized and Quenched, Surface Hardness 56-62HRC

Output Shaft: 45# Steel

Input Shaft: 20Cr Steel

Packaging

Carton and Wooden Case

Bearing

C&U Bearing (Renben)

Seal

SKF

Warranty

12 Months

Input Power

0.12kW~15kW

IEC Flange

B5/B14/Flange (6060cm, 8080cm, 9090cm, 104104cm, 110110cm, 130130cm, 180*180cm)

Lubricant

GB L-CKC220-460, Shell Omala220-460

Applications

Industrial Automation Equipment,Logistics, Food,Packaging Equipment and so on

Hot Tags: rv 110 worm gear, China rv 110 worm gear manufacturers, suppliers, factory, RV 150 Worm Gear, cylindrical worm gear, worm gearbox reducer, worm gear housing, jual worm gearbox, small worm gear box